Steam Generator SS77

Steam Generator SS77

Create amazing woodworking projects with bent wood

  • Works great for wood bending projects
  • Compact electric steamer runs on a standard current with built in thermal protection
  • Includes instructions on how to build your steam box and a steam box adaptor so you can be bending the same day

image

Steam Generator SS77

Steam Generator SS77 Features


button-retail-stores


steam-generator-ss77 Steam Generator SS77

Download

Q. The spray is very blotchy/splatters. What can I do?
A. The paint requires thinning further (100 – 200ml of the appropriate thinner).

Q. What might be wrong if Intermittent spraying occurs?
A. The Pick-up Tube is loose. Push in.
A. The Paint Container is not tight enough. Hold the Paint Container and turn the Spray Gun.
A. The paint requires more thinning/mixing.

Q. It has stopped spraying during use. What might be wrong?
A. The Fluid Tip may be blocked with paint. Also, check the air feed hole underneath the Fluid Tip.

Q. I am getting an ‘orange peel’ effect. What can I do?
A. The paint is being applied too thick. Turn the volume down, spray lighter coats, and use a smaller Fluid Tip and Needle.
A. The paint is drying before it hits the surface. Hold the Spray Gun closer to the item being sprayed.
A. Spray Gun is not being held perpendicular to surface. Keep wrist and arm straight and move whole body. Keep Spray Gun an even distance from surface.

Q. Can I get different sized Fluid Tips?
A. Yes you can get 1.0mm, 1.5mm and 2.5mm for the HV5000 and HV7000 and 1.5mm, 2.5mm for the HV1900, HV3901.

Q. Will the SprayStation spray exterior emulsion/masonry paint?
A. Yes, but with sufficient dilution and a 2.5mm Fluid Tip. This is better for walls and smaller areas rather than a whole house exterior because you will need to apply approximately 3 coats.

Q. Do I need to mask anything?
A. Although there is minimum overspray with HVLP technology you will always get a spray mist in the atmosphere, so it is advisable to mask over appliance sockets, light fittings etc. Also, cover any furniture in the area you are spraying with appropriate sheeting.

Q. Can I use paint in the 4l Spray Pack?
A. No, only fence treatment or very thin liquids.

Q. Will the Spray Gun I use spray different types of paint?
A. Yes, but for different thicknesses different size Fluid Tips are available to achieve an improved finish. For example, 1.5mm for gloss paint.

Q. Does the viscosity guide cover all types of sprayers?
A. No, it is only for Earlex SprayStations.

Q. I have thinned the paint to the correct viscosity but it splatters everywhere, what can I do?
A. You will need to thin it further. The viscosity test is a general guide to get the paint flowing. The timings can vary amongst various paint manufacturers. Try adding 100 – 200ml of the appropriate thinner then stir. Next, lift out your stirrer and the paint should be running off it rapidly. When it starts dripping the drops should be perfectly round like rain drops and not clingy or lumpy.

Q. What do I thin the paint with?
A. Water if water based. White spirit if solvent based. Cellulose if cellulose based.

Q. Can I spray Hammerite?
A. It is possible to spray but you will need to thin it nearly 50:50 with Hammerite thinners.

Q. The paint I want to spray says ‘for brush or roller use only’. Can I spray this?
A. This is usually because the paint manufacturer does not test it fo spraying, However, most will spray with dilution. Always check with the manufacturer or our service department first.

Q. Can I use my SprayStation for artificial suntan solution?
A. No, the unit is not certified for this use or any other use not specified in the instructions. It will also invalidate the manufacturer’s guarantee.